Binary files read and write
EDIT: https://github.com/cclauss/SPLnFFT_tools contains the code created based on this thread. Please open issues and/or submit pull requests to improve that code.
I created read() and write() with the
arraymodule and again with the
structmodule. It seems like much more work than just reading and writing
jsonfiles which are far more portable and remove all the machine-specific abnormalities. https://github.com/cclauss/SPLnFFT_tools/blob/master/old_code/binary_file_of_2d_matrix.py
Thanks to CCC for this valuable piece of code which teaches a lot about dealing with binary data imported from other Apps. In my case, it is raw float data of SPL measurements organized in two columns for both Slow and Fast time weightings that were imported from Dropbox with a script available in this Forum. I wonder why 2D or nD arrays have to be dealt as structures in Python.
I'll test it and will report the results. Thanks again
The sample script works fine and now I understand the process. Just a further question: For reading only my binary file with floating point data, like 'MYSPLDATA.BIN' how should I define the 2D array? , and do I need to initialize it with some value, as in the sample script?.
What is SPL? What kind of computer writes the SPL datafile? What program on that computer writes the SPL datafile? Is there any documentation on the SPL format? Is there a sample SPL file with know values?
I would start with:
And see if the values look good.
The App is SPLnFFT for iOS. Your script works fine in Array mode with the only exception of this instruction: floats_in_the_file = os.path.getsize(filename) / struct.calcsize('f')
I just noticed that you changed the source code of the script. Now it reads 5MB binary data in about 4 seconds using the Array Mode. I'll check the Structure Mode and report results. Congratulations
How can I access the data in the 2D array to make plots and numeric calculation of aggregated data?. The App saves 5MB data for a 24 hours recording. If the recording time is shorter it pads data with zeroes. Is there a way to filter out this values while reading the file?. The total data saved in float format is computed as follows: count=2436008*2;
There was an error count=24 * 3600 * 8 * 2; Sorry
ManuelU last edited by ccc
Here is a short sample of the values read by your script in Array Mode. Observe the zero values at the end.
(50.56001281738281, 53.25138854980469), (51.46320724487305, 59.16133117675781), (53.85163116455078, 56.33137512207031), (54.70978546142578, 54.6609001159668), (55.20241165161133, 47.02310562133789), (55.262977600097656, 40.11175537109375), (54.45186996459961, 43.808773040771484), (54.05076217651367, 42.50151824951172), (53.665225982666016, 54.5957145690918), (53.8406867980957, 65.96211242675781), (58.009944915771484, 65.0105972290039), (59.889801025390625, 59.607154846191406), (60.222530364990234, 56.390960693359375), (60.41679763793945, 54.57362747192383), (60.55101776123047, 41.55317687988281), (60.54636001586914, 40.97874450683594), (60.54383850097656, 46.896514892578125), (60.42774200439453, 45.11729049682617), (57.88348388671875, 49.7500114440918), (53.61359786987305, 46.01418685913086), (50.81377410888672, 36.51190185546875), (48.24237823486328, 31.083229064941406), (44.919986724853516, 32.971107482910156), (44.69907760620117, 46.87627410888672), (45.31845474243164, 39.48908233642578), (44.62737274169922, 35.4039192199707), (44.04755401611328, 34.72141647338867), (41.45051956176758, 34.2315673828125), (39.6866569519043, 33.11891174316406), (39.542598724365234, 50.92300796508789), (43.85606002807617, 34.235633850097656), (43.871002197265625, 40.384735107421875), (42.935977935791016, 52.999149322509766), (46.3834228515625, 52.6627311706543), (48.203895568847656, 57.949790954589844), (51.57520294189453, 52.208770751953125), (52.15311050415039, 45.712528228759766), (52.26800537109375, 50.851497650146484), (52.261497497558594, 46.12493133544922), (52.383358001708984, 84.88561248779297), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0), (0.0, 0.0)
How can I access the data in the 2D array to make plots and numeric calculation of aggregated data?
I am unclear what you mean. Your last post looks to me like it is a list of (x, y) tuples. What else do you need?
To remove all (0.0,0.0) elements from your list...
my_list = [(x, x) for x in my_list if x and x] # remove all (0.0,0.0) elements
count=24 * 3600 * 8 * 2
count = 24 (hours in a day) * 60 (minutes in an hour) * 60 (seconds in a minute) * 8 (what is this? (samples per second?)) * 2 (values (fast and slow?))
Thera are two weighting times for SPL meters : SLOW = 0ne reading per second; FAST = one reading every 1/8 of second. That means that you have a pair of eight data points every second. One minute has 60 seconds so you have 60 * 60 = 3600 seconds per hour. One hour has 3600 * 8 * 2 = 57600 data points in float format that are exported to Dropbox. Another problem are the NAN AND infinite values generated for many reasons, that have to be replaced by the previous SLOW or FAST recorded values. They are mostly negative values. As you can observe, there is a post processing job to be done before plotting or computing aggregated data to render reliable results.
The total size of any file exported to Dropbox by the App SPLnFFT Noise Meter is 5529600 Bytes, therefore each data point in float format uses 4 Bytes. (24 * 3600 * 8 * 2 = 1382400) * 4 = 5529600. I've observed that The instruction: floats_in_the_file = os.path.getsize(filename) / struct.calcsize('f') reads a lot of garbage where is supposed to read zeroes.
structapproach generate the same list?
What is printed if you add
print(floats_in_the_file)when you run the script against a 5529600 byte file? I would expect
You could try removing bogus values by post-processing the list with:
my_list = [(x, x) for x in my_list if x > 0 and x > 0] # remove invalid elements
You are right, the maximum number of data points in the binary file is 1382400. I'm new in Phytonista and I'll have to read how to detect and remove NaN an Infinite values in Phyton and what are the available Array functions. I've an Academic Apple Developer License and I'm exploring all the available options to process the noise data within the IOS environment with an Universal standalone App. As far as I know, Phytonista seems to be the only one to import SPL data with a script from the Dropbox to its sandbox, overriding the cumbersome iTunes File Sharing. The project is part of an epidemiological investigation on Environmental Noise and Health which includes, among other challenges, the simultaneous recording of an ECG.
Thanks for your valuable help.
OK... In just over 1 second
SPLnFFT_Reader.pyreads 1,382,400 floats out of the binary file, converts that into a 2d list of 691,200
fast_slowpairs and cleans that down to a 2d list of 2,786 valid
fast_slowpairs and prints out the first 50 pairs.
My cleansing step might not be right for your purposes. You can use
math.isinf()to find those values but I do not believe that it is required anymore because the author of the SPLnFFT app told me in an email that "In the matlab [example] script there is some processing to get rid of NaN data. But I thought I had solved this in latest release of SPLnFFT".
numpy gurus... Why does this not work as expected?
import numpy data = numpy.fromfile('SPLnFFT_2015_07_21.bin', dtype=float) print(len(data)) # 691200 :-( this is half of the expected number
omz last edited by
You can try this:
data = numpy.fromfile('SPLnFFT_2015_07_21.bin', dtype=numpy.dtype('f4'))
floatdata type is usually implemented as a
double(8 bytes), so this specifies the number of bytes explicitly.
Phuket2 last edited by
Do issues still exist with byte order on different platforms? I really don't know. A long time ago, we used to have to consider this. Big and little Indien when reading binary/memory files without an API that took care of the translation
Yes. Complexity is preserved but it is better hidden. The fortunate thing here is that the file in question was written out by one iOS app (SPLnFFT) and read in by another iOS app (Pythonista) so byte order is not an issue.